Professionally installed interior drainage that manages groundwater and hydrostatic seepage before it reaches your finished floor or stored belongings.
Effective, proven, and installed without disturbing your yard or exterior features.
Interior systems are installed entirely from inside the basement, eliminating the landscaping and hardscaping disruption that exterior work requires.
Perimeter channels capture water as it enters at the floor-wall joint and route it to a sump pit before it can spread across the basement floor.
Interior drainage is not weather-dependent. Installation can proceed in winter months when exterior excavation and membrane work are not feasible in Hancock, WI conditions.
Gravity-fed channel designs minimize pump cycling frequency, extending pump service life and reducing electricity usage.
An interior drainage system addresses basement moisture by capturing and redirecting groundwater after it has entered the building envelope at the floor-wall joint or through weep holes at the base of the foundation wall. This differs fundamentally from exterior waterproofing, which prevents water from reaching the wall surface. Interior drainage accepts that water will enter under certain pressure conditions and provides a managed pathway for that water to reach a collection point without spreading across the basement floor or damaging finished materials. For Hancock homes where exterior excavation is impractical, cost-prohibitive, or where the moisture entry is concentrated at the perimeter footing level, interior drainage is the technically appropriate solution.
Once the trench is cut, the system design determines how effectively water is captured. Basic systems use a simple gravel bed with a perforated pipe to collect and route water. More advanced channel profiles, often called proprietary drainage channel systems, incorporate a raised profile that sits slightly above the footing and captures not just floor-joint seepage but also water migrating down the wall face. A wall flange component extends up behind any baseboard or framing material to intercept water running down the wall before it reaches the floor level. This wall flange detail is important in situations where the moisture entry is not strictly at the floor joint but extends up the lower wall section, which is common in Hancock homes with older block or stone foundations where the mortar has deteriorated.
The sump pit integration is the component that makes an interior drainage system fully functional. The channel system routes water to the pit, and the pump removes it from the pit before it overflows. Pit location is determined by the channel routing geometry, existing pit locations if present, and access to a discharge route. In some Hancock homes where the basement has been partially finished, the channel must be routed around finished walls and mechanicals to reach an optimal pit location. These routing decisions are made during the assessment and documented in the installation plan. The pit itself is sized to provide adequate storage volume for the expected inflow rate, ensuring the pump is not short-cycling and the system has adequate buffer during peak inflow events.
The honest tradeoffs of interior drainage versus exterior waterproofing are something we address directly during every assessment in Hancock. Interior drainage is less invasive, faster to install, unaffected by seasonal weather constraints, and generally less expensive per linear foot than exterior excavation and membrane work. However, it does not eliminate the moisture that is contacting the wall surface; it captures and removes water after it enters the building envelope. For homeowners whose primary concern is protecting finished basement space from water accumulation on the floor, interior drainage addresses that objective effectively. For homeowners concerned about long-term wall deterioration from moisture contact, or whose walls show active spalling and efflorescence from chronic wet conditions, the exterior treatment addresses the wall moisture directly. When both conditions are present in the same structure, we discuss a combined approach that treats both the wall surface and manages floor-level seepage.
From perimeter channel installation to sump integration and annual service, a complete interior drainage solution.
Our full perimeter systems capture seepage from every wall section, routing it to the sump pit regardless of which foundation wall is experiencing the greatest inflow at any given time.
Learn moreFor Hancock homes where moisture entry is concentrated on one or two walls, targeted channel installation along the affected sections provides effective protection at lower cost than full perimeter treatment.
Get an assessmentThe wall flange component extends the drainage channel up behind the base of the wall to capture moisture migrating down the wall face before it reaches the floor.
Ask about wall flangesInstalling a new pit or relocating an existing one to optimize channel routing geometry and pump efficiency. Proper pit placement is the key to gravity-assisted drainage performance.
Plan your pit locationA drainage system that was properly installed years ago but has degraded can often be restored through cleaning and targeted component replacement at far less cost than a full reinstallation.
Schedule an inspectionWhen a previously installed partial channel system needs to be extended to address additional wall sections, we design and install the expansion with clean transitions to the existing channel and updated sump pit capacity if required.
Expand your systemFour stages from assessment to operational system, each one documented and verified before the next begins.
We inspect the basement under controlled conditions to document exactly where and how water is entering your Hancock home. We look for staining patterns, efflorescence location, floor-joint seepage evidence, and any wall-face moisture migration. This documentation determines the channel scope and routing.
Cut dimensions are verified before the gravel bed is placed to confirm the channel profile will sit at the correct elevation relative to the footing.
Each connection point between channel sections is inspected before the next section is placed to confirm continuity and proper slope transition.
New concrete is poured over the channel system, restoring the floor surface and permanently enclosing the drainage installation. After cure, the full system is tested by introducing water at multiple points along the channel and verifying flow to the sump pit and pump activation.
Real words from real customers, after their first season with an interior drainage system installed.
The assessment was thorough and they explained exactly which wall sections were causing the problem. The installation took one day and the crew cleaned up completely before leaving. The following spring, which was wet, produced zero water on the basement floor for the first time in seven years.
Our older block foundation was not a candidate for exterior work without major landscaping disruption. The interior channel system gave us the protection we needed without touching the exterior at all. The wall flange detail they added captured the seepage that was running down the bottom block course, which was the main issue.
We had the system installed in November, which would have been impossible with exterior work given the ground conditions that time of year. The interior installation was unaffected by weather and completed in a single day. The system handled a major rain event the following week perfectly.
What you need to know to make a confident decision about interior drainage.
The installation begins with saw-cutting the basement floor slab along the planned channel route, typically four to six inches from the foundation wall. The cut follows the interior perimeter of the basement and terminates at the sump pit location. Concrete is removed and the subbase is excavated to reach the footing level, then a gravel bed is placed, the drainage channel profile is set to slope toward the pit, and the wall flange is installed where specified. New concrete is poured to cap the system and restore the floor surface. Most residential installations in Hancock are completed in a single working day for standard perimeter configurations.
Interior drainage is a long-term system, not a temporary repair, when it is properly installed and the channel is correctly sized for the inflow volume. The channel system itself has no moving parts and requires no maintenance beyond occasional inspection. The gravel bed does not compact or break down under normal conditions. The drainage profile materials used in quality installations are rated for permanent soil-contact use. Systems installed decades ago continue to perform when the sump pump is maintained and the channel has not been blocked by slab settlement or debris infiltration.
Interior drainage typically costs less per linear foot than exterior excavation and membrane waterproofing, primarily because the excavation equipment, soil management, and backfill work associated with exterior projects add significant cost to that scope. For most standard residential configurations in Hancock, interior drainage is a more budget-accessible solution. However, cost comparison alone should not drive the decision; the correct approach depends on the moisture entry mechanism present in your specific basement. Installing interior drainage to address a problem that is fundamentally an exterior membrane failure will provide comfort improvement but will not stop ongoing wall contact moisture, which continues to deteriorate the wall material.
Standard full perimeter interior drainage installation for a typical single-story Hancock basement is completed in one working day. Partial perimeter systems on one or two walls are typically finished in half a day. Basements with complex layouts, finished areas requiring careful routing, or multiple existing pipe penetrations crossing the channel path may extend the installation to a second day. We provide an accurate time estimate after the assessment so homeowners can plan for the dust and noise associated with saw-cutting, which is the most disruptive phase of the installation.
An interior drainage channel system requires minimal maintenance because it has no moving parts. The primary maintenance task is ensuring the sump pump connected to the system is in good working order, which involves the same inspection protocol as any pump: float switch testing, motor operation check, discharge line inspection, and battery backup readiness verification. The channel itself should be visually inspected at accessible cleanout points annually if the design includes them, or whenever pump performance changes in a way that might indicate a channel blockage. Older channel installations in some Hancock homes show calcium and mineral deposit buildup over many years, which can be addressed with periodic flushing.
Interior drainage can be installed in a finished basement, though the process requires more planning and may involve temporary disruption of finished flooring and baseboard materials along the channel route. The saw-cutting must follow the perimeter regardless of what is installed above it, so finished flooring within the cut zone will need to be removed before work begins and replaced after the concrete cap cures. Drywall along the base of finished walls is typically removed at least partially to allow the wall flange to be installed properly. We document all disruption areas in the installation plan so homeowners can arrange for finish materials before scheduling the work.
No excavation. No landscape disruption. Just a properly installed channel system that manages water at the point of entry, year after year.
Call +1-866-476-1348 for Assessment